Conair MPW Specifiche Pagina 13
- Pagina / 119
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Actual temperature of water supplied to the mold is
higher than the setpoint deviation limit allows.
1. High deviation temperature is set too low. Increase.
2. Water has stopped flowing between supply outlet and
return inlet. Check for plugged pipe or failed cooling
valve.
3. The heater contact failed. Replace the contactor.
4. The heater and lines may be too
large for this application.
Actual temperature of water supplied to
the mold is higher than the programmed
190˚ F safety limit.
1. Water has stopped flowing between supply outlet and
return inlet. Check for closed valve or plugged line.
2. The heater contactor failed. Replace contactor.
Actual temperature of water supplied to
the mold is below the programmed 20˚ F
safety limit.
1. The cooling valve is stuck open. Clean valve.
2. The heater has failed. Check for a bad heating element,
or a heater contact that failed in the open position.
The incoming power is out of phase. A
leg may have failed or is disconnected.
1. The pump is rotating in the wrong direction. Reverse any
two leads on the power connection.
2. Check fuses or circuits at the main power supply.
The return line temperature probe failed.
Check for loose connections, or replace.
The supply line temperature probe failed.
Check for loose connections, or replace.
The pump fuse failed.
Replace the fuse on the motherboard.
NOTE: See the Thermolator User Guide for additional alarm mes-
sages regarding fuses and controller errors.
TROUBLESHOOTING
Shut down alarms
The Thermolator has shut down automatically to prevent
damage to equipment or personnel. To resume normal
operation, press , fix the problem, then press .
The pump overload has tripped. Contact is open.
1. Verify that the correct voltage is supplied to the motor.
2. Water flow may be more than the pump can handle.
Check current draw against motor rating. Decrease flow
as needed.
The supply water level is low.
1.Verify that the water supply is turned on.
NOTE: The low water pressure alarm does not require manual
reset. It will reset automatically when the water level is sufficient.
The actual temperature of water supplied to the mold
exceeds the 190˚ F temperature safety switch limit.
1. The unit is not running. Start the Thermolator.
2. Water has stopped flowing between supply outlet and
return inlet. Check for closed valve or plugged line.
3. The heater contactor failed. Replace contactor.
If there is a problem, the Thermolator
®
activates the red Alarm light
and changes the RUN/STOP light from green to flashing red.
Press to silence the optional audible alarm.
Check the indicator lights and messages
to help determine the cause of the problem.
Warning alarms
The Thermolator continues operating, but this problem
could lead to a shutdown condition if not corrected.
Actual temperature of water supplied to the mold is
lower than the setpoint deviation limit allows.
1. Low deviation temperature is set too low. Increase.
2. The heater failed. Check for a bad heating element or a
heater contact that failed in the open position.
3. The cooling valve is stuck open. Clean valve as needed.
Stop Run
WARNING: Before servicing the Thermolator
®
Allow the unit to cool to below 100˚ F. Disconnect and lockout
the main power source. Disconnect water and air supply lines.
!
1
2
Low Deviation
High Deviation
SPI Communication
FUS
002
PbS
Err
Pbr
Err
Hi
SAF
Lo
SAF
PHS
Err
Pump
Pump
High Temp. Safety
Low Water Pressure
QCH006/1197 © 1997
Positive/Negative Water
Temperature Controller
with TW-2 Microprocessor
Quick Card
Thermolator
®
vacuTrac
The Conair Group, Inc.
One Conair Drive
Pittsburgh, PA 15202
Phone: (412) 312-6000
Fax: (412) 312-6001
Basic
Operation
Troubleshooting
Instant Access Parts
& Service:
(800) 458-1960
(814) 437-6861
www.conairnet.com
- Thermolator 1
- TEMPERATURE 2
- AND STOP 2
- MOLD LEAKS 2
- TPHF017/1101 3
- CONTROLS 4
- SPECIFICATIONS NOTES: 5
- SEQUENCE OF OPERATION 6
- TROUBLESHOOTING A VTR UNIT 7
- Figure 1 8
- Starting the Thermolator 12
- Stopping the Thermolator 12
- TW-1 and TW-2 16
- Please record your 17
- TABLE OF 18
- CONTENTS 18
- INTRODUCTION 20
- READ THIS SO NO 22
- EAD THIS SO NO 23
- ONE GETS HURT 23
- 1-4 INTRODUCTION 23
- DESCRIPTION 24
- WHAT IS THE 25
- THERMOLATOR ? 25
- HOW IT WORKS: 26
- INJECTION 26
- SPECIFICATIONS 29
- FEATURES AND 31
- INSTALLATION 32
- UNPACKING THE 33
- PREPARING FOR 34
- CONNECTING 35
- PROCESS AND 35
- WATER SUPPLY 35
- PURGE VALVE 36
- TESTING THE 38
- 3-8 INSTALLATION 39
- CHANGING 40
- ENABLING AND 41
- DISABLING 41
- PASSCODE 41
- PROTECTION 41
- SELECTING THE 43
- CONTROL POINT 43
- DEVIATION 45
- ACTIVATING SPI 46
- INSTALLING THE 47
- AUTO START 47
- OPERATION 50
- 4-2 OPERATION 51
- TW-2 CONTROL 52
- MOUNTING THE 53
- LOCATION 53
- ENTERING A 54
- STARTING THE 55
- STOPPING THE 56
- USING THE 57
- MANUAL PURGE 57
- PERATION 4-9 58
- PERFORMING AN 59
- AUTO TUNE 59
- MAINTENANCE 62
- PREVENTATIVE 63
- SCHEDULE 63
- PERFORMING SYSTEM 64
- CHECKING THE 65
- FLUID LEVEL IN 65
- RESERVOIR 65
- AINTENANCE 5-5 66
- KEY/DISPLAY 67
- INPUT TEST 68
- OUTPUT TEST 69
- DISABLING OR 70
- ENABLING 70
- MONITORS 70
- CALIBRATING 71
- OPERATING 73
- TROUBLESHOOTING 74
- A FEW WORDS 75
- HOW TO IDENTIFY 76
- CAUSE OF A 76
- SHUT DOWN 77
- Possible cause 78
- Solution 78
- HUT DOWN 78
- 6-8 TROUBLESHOOTING 81
- 6-10 TROUBLESHOOTING 83
- WILL NOT 85
- POWER UP 85
- CHECKING AND 86
- REPLACING 86
- RESETTING 87
- OVERLOADS 87
- REPLACING THE 87
- PUMP OVERLOAD 87
- MOTHERBOARD 88
- CONTACTOR 89
- CHECKING 90
- THERMOCOUPLES 90
- REPAIRING 91
- SOLENOID 91
- EPAIRING 92
- ELEMENTS 93
- REMOVING 95
- DISASSEMBLING 96
- ASSEMBLING 96
- - 2 HP PUMPS 96
- 3 - 7.5 HP PUMPS 97
- WE’RE HERE 100
- PPENDIX A-2 101
- DIAGRAMS 102
- ECHNICAL INFORMATION 104
- SPI COMMANDS 106
- SUPPORTED BY 106
- THERMOLATOR 106
- SPI STATUS WORDS 107
- Status, Machine 2 109
- 7439-97-6 110
- /DIAGRAMS 112
- SPARE PARTS 113
- IRING DIAGRAM 116
- IRCUIT BOARD UGH015/0100 117
Prodotti e manuali riguardandi no Conair MPW
no Conair BTS4C Istruzioni per gli Interventi
(10 pagine)
(10 pagine)
no Conair MPA Informazioni Techniche
(86 pagine)
(86 pagine)
no Conair MPW Guida Utente
(60 pagine)
(60 pagine)
no Conair MPA Informazioni Techniche
(17 pagine)
(17 pagine)
no Conair 0.25 to 1.5 ton Informazioni Techniche
(44 pagine)
(44 pagine)
no Conair VL Series Informazioni Techniche
(80 pagine)
(80 pagine)
no Conair FC-33 Guida Utente
(58 pagine)
(58 pagine)
no Conair 0.25 to 1.5 ton Guida Utente
(100 pagine)
(100 pagine)
no Conair EARTHSMART ECM Series Guida Utente
(72 pagine)
(72 pagine)
no Conair S900II System Manuale Utente
(32 pagine)
(32 pagine)
no Conair VL Series Manuale Utente
(4 pagine)
(4 pagine)
no Conair MPA Informazioni Techniche
(30 pagine)
(30 pagine)
no Conair S900II System Manuale Utente
(35 pagine)
(35 pagine)
Jumo 60.3031 Surface-mounting thermostats, ATH.-SE Data podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Ekwipunek Jumo 60.3031 Surface-mounting thermostats, ATH.-SE Data.
Dostarczamy 3 pdf podręczników Jumo 60.3031 Surface-mounting thermostats, ATH.-SE Data do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Jumo 60.3031 Surface-mounting thermostats, ATH.-SE Data Instrukcja Użytkownika (6 strony)
Marka: Jumo | Kategoria: Equipment | Rozmiar: 0.17 MB |
Spis treści
Jumo 60.3031 Surface-mounting thermostats, ATH.-SE Data Instrukcja Użytkownika (6 strony)
Marka: Jumo | Kategoria: Equipment | Rozmiar: 0.17 MB |
Spis treści
Jumo 60.3031 Surface-mounting thermostats, ATH.-SE Data Instrukcja Użytkownika (6 strony)
Marka: Jumo | Kategoria: Equipment | Rozmiar: 0.18 MB |
Więcej produktów i instrukcji dla Ekwipunek Jumo
| Modele | Rodzaj dokumentu |
|---|---|
| 60.3031 Surface-mounting thermostats, ATH.-SE Oper |
Instrukcja Użytkownika
JUMO 60.3031 Surface-mounting thermostats, ATH.-SE Operating Manual Benutzerhandbuch,
24 strony
|
| 60.3031 Surface-mounting thermostats, ATH.-SE Oper |
Instrukcja Użytkownika
JUMO 60.3031 Surface-mounting thermostats, ATH.-SE Operating Manual User Manual,
24 strony
|
| 60.3031 Surface-mounting thermostats, ATH.-SE Oper |
Instrukcja Użytkownika
JUMO 60.3031 Surface-mounting thermostats, ATH.-SE Operating Manual Manuel d'utilisation,
24 strony
|
| 60.3031 Surface-mounting thermostats, ATH.-SE Oper |
Instrukcja Użytkownika
JUMO 60.3031 Surface-mounting thermostats, ATH.-SE Operating Manual Manual del usuario,
24 strony
|
| 603026 Surface-Mounted Double Thermostat ATH Data |
Instrukcja Użytkownika
JUMO 603026 Surface-Mounted Double Thermostat ATH Data Sheet Benutzerhandbuch,
10 strony
|
| 603026 Surface-Mounted Double Thermostat ATH Data |
Instrukcja Użytkownika
JUMO 603026 Surface-Mounted Double Thermostat ATH Data Sheet User Manual,
10 strony
|
| 603021 Surface-Single Mounted Thermostat, ATH seri |
Instrukcja Użytkownika
JUMO 603021 Surface-Single Mounted Thermostat, ATH series Operating Manual User Manual,
2 strony
|
| 603026 Surface-Mounted Double Thermostat ATH Data |
Instrukcja Użytkownika
JUMO 603026 Surface-Mounted Double Thermostat ATH Data Sheet Manuel d'utilisation,
10 strony
|
| 603021 Surface-Single Mounted Thermostat, ATH seri |
Instrukcja Użytkownika
JUMO 603021 Surface-Single Mounted Thermostat, ATH series Data Sheet Benutzerhandbuch,
10 strony
|
| 603021 Surface-Single Mounted Thermostat, ATH seri |
Instrukcja Użytkownika
JUMO 603021 Surface-Single Mounted Thermostat, ATH series Data Sheet User Manual,
10 strony
|
| 603021 Surface-Single Mounted Thermostat, ATH seri |
Instrukcja Użytkownika
JUMO 603021 Surface-Single Mounted Thermostat, ATH series Data Sheet Manuale d'uso,
5 strony
|
| 603021 Surface-Single Mounted Thermostat, ATH seri |
Instrukcja Użytkownika
JUMO 603021 Surface-Single Mounted Thermostat, ATH series Data Sheet Manuel d'utilisation,
10 strony
|
| 60.1540 Flue gas temperature monitor, STM-RW-2 Dat |
Instrukcja Użytkownika
JUMO 60.1540 Flue gas temperature monitor, STM-RW-2 Data Sheet Benutzerhandbuch,
4 strony
|
| 60.1540 Flue gas temperature monitor, STM-RW-2 Dat |
Instrukcja Użytkownika
JUMO 60.1540 Flue gas temperature monitor, STM-RW-2 Data Sheet User Manual,
4 strony
|
| 60.1540 Flue gas temperature monitor, STM-RW-2 Dat |
Instrukcja Użytkownika
JUMO 60.1540 Flue gas temperature monitor, STM-RW-2 Data Sheet Manuel d'utilisation,
4 strony
|
| 60.1540 Flue gas temperature monitor, STM-RW-2 Ope |
Instrukcja Użytkownika
JUMO 60.1540 Flue gas temperature monitor, STM-RW-2 Operating Manual User Manual,
2 strony
|
| 601530 Rod Thermostat Data Sheet |
Instrukcja Użytkownika
JUMO 601530 Rod Thermostat Data Sheet Benutzerhandbuch,
6 strony
|
| 601530 Rod Thermostat Data Sheet |
Instrukcja Użytkownika
JUMO 601530 Rod Thermostat Data Sheet User Manual,
6 strony
|
| 601530 Rod Thermostat Data Sheet |
Instrukcja Użytkownika
JUMO 601530 Rod Thermostat Data Sheet Manuel d'utilisation,
6 strony
|
| 14597 safetyM TB/TW08 Temperature Limiter and Temp |
Instrukcja Użytkownika
JUMO 14597 safetyM TB/TW08 Temperature Limiter and Temperature Monitor Data Sheet Benutzerhandbuch,
10 strony
|
© 2020, manymanuals.it. Tutti i diritti riservati | 0.018 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale